OSHA 3080 defines a power tool as any tool requiring external electrical, pneumatic, or chemical power to function.
1. Wear safety glasses at all times upon entering a lab situation.
2. Check wood stock for defects before cutting, such as knots, cracks, and foreign objects . 3. Plan sawing procedures so there is a maximum of forward feed and a minimum of backing out.
4. Cut only flat stock whenever possible. When cutting dowels or other round stock, use approved holding device and get permission for this special setup.
5. Be sure the saw blade is the proper width for the job being done.
6. Blades are different widths and may require relief cuts to be made when cutting small radius curves.
7. Hold any wood firmly on the table and not up off the table.
8. Set the upper blade guide ¼” or less above the wood to be cut.
9. Always keep fingers out of the path of the blade and a safe distance from the blade.
10. Feed material into the blade at a moderate rate of speed.
11. Allow the machine to come to a complete stop before backing out of a long cut. Do not back out of a cut with the machine running. This can pull the blade off of the wheels.
12. Turn off the power after using the band saw and stand by until the machine has come to a complete stop.
13. Keep the table clear of scraps and clean table of scraps after the blade stops moving. Never pick pieces of wood from the machine while it is in motion and then it is wise to use a push stick or brush.
14. Make all adjustments while the machine is off and stopped.
15. When handling long pieces of wood, get help and do the pushing yourself.
17. When operating the machine, keep well balanced and stand carefully to avoid injury from unexpected slips or falls.
19. When a band saw blade breaks or comes off the wheels, step away immediately, shut off the power without endangering yourself, and then notify shop personnel.
19. Always keep clear of the area to the right of the band saw when it is being used because if the blade breaks it may whip out into this area.
20. Check the blade for cracks or splits before using the band saw. If a crack is found, unplug the machine and notify shop personnel.
21. Listen for tell-tale sounds as you cut. A clicking sound may mean a cracked blade.
22. When making adjustments it is a wise practice to unplug the machine to avoid accidental starts.
23. Turn on the dust collection system and close all gates, except that for the band saw.
Drilling machines, or drill presses, are primarily used to drill or enlarge a cylindrical hole in a workpiece or part. The chief operation performed on the drill press is drilling, but other possible operations include: reaming, countersinking, counterboring, and tapping.
1. Prior to drilling a hole, locate the hole by drawing two crossing lines. Use a center punch to make an indentation for the drill point to aid the drill in starting the hole.
2. Select the proper drill bit according to the size needed.
3. Select an appropriate size center drill.
4. Select a cutting fluid when necessary.
5. Properly secure the workpiece to the table.
6. Select the correct RPM for the drill bit. Take into account: size of bit, material, and depth of hole to be drilled.
7. Use an interrupted feed, called peck drilling, to break up the chips being produced.
8. Pilot holes should be used on holes larger than 3/8” dia. Holes are to be enlarged in no more than 1/4” increments.
9. Clean the drill press and surrounding area when finished.
1. No attempt should be made to operate a drill press until you are certain you understand the proper procedures for its use.
2. Dress appropriately. Remove all watches and jewelry. Safety glasses or goggles are a must.
3. Plan out your work thoroughly before starting.
4. Know the location of the OFF button.
5. Clamp all work securely to the table.
6. Always remove the chuck key immediately after using it. A key left in the chuck will be thrown out at a high velocity when the machine is turned on. Never let the chuck key leave your hand except to put it back into its holder.
7. Never stop a drill press spindle with your hand after you have turned off the machine. Chips often build up around the chuck.
8. Use a brush, not your hands, to remove chips from the machine. Do not clean up while the machine is running.
9. Remove burrs from drilled workpieces as soon as possible.
10. Keep the floor area clean. Immediately wipe up any oil spills.
1. Always wear eye protection when operating circular saws.
2. Tie up loose clothing and hair, and remove jewelry that could be pulled into the saw. Hearingprotection is also recommended as saws are very loud and can lead to hearing loss.
3. Verify that the saw blade or abrasive cutting disc has a RPM rating ABOVE the saw RPM.
4. Set the saw cutting depth as shallow as possible – avoid letting the blade protrude much below the stock being cut.
5. Never set a circular saw down unless the blade has completely stopped.
6. Make adjustments and change blades only when unplugged.
7. Do not hold or force the retracting lower guard in the open position.
8. Do not place hand under the shoe or guard of the saw.
9. Do not over tighten the blade-locking nut.
10. Do not twist the saw to change, cut or check alignment.
11. Do not use a saw that vibrates or appears unsafe in any way.
12. Do not force the saw during cutting – forcing can cause kickback.
13. Do not cut materials without first checking for obstructions or other objects such as nails and screws.
14. Do not carry the saw with a finger on the trigger switch.
15. Do not overreach and make sure to keep proper footing and balance.
16. Do not rip stock without using a wedge or guide clamped or nailed to the stock.
17. Make sure the stock will not fall and “bind” the circular saw – kickback can occur.
Miter Saw Safety
Instructional Video: http://www.youtube.com/watch?v=kFs-30mFU1A
1. Always wear eye protection when using the miter saw.
2. Use clamps to support workpiece whenever possible. If supporting the workpiece by hand, you must always keep hand outside of “No Hand” area that is marked in yellow. Never feed the workpiece into the blade or cut freehand in any way.
3. Do not use this saw to cut pieces that are too small to be securely clamped, or that require your hand be placed in the “No Hand” area near the blade. When cutting small or irregularly shaped pieces first attach the workpiece to a jig/fixture.
4. Do not reach in back of the saw blade behind the fence with either hand to hold down or support the workpiece, remove wood scraps, or for any other reason.
5. Never cross your hand over intended line of cutting. Supporting the workpiece “cross-handed” i.e. holding the left side of the workpiece with your right hand is very dangerous.
6. Always disconnect the power cord from the power source before making any adjustments or attaching any accessories.
7. Only use the miter saw to cut wood or wood-like materials.
8. Inspect your workpiece before cutting. If workpiece is bowed or warped, clamp it with the outside bowed face toward the fence. Always make certain that there is no gap between the workpiece, fence and table along the line of cut. Also, make sure there are no nails or foreign objects in the workpiece.
9. Do not use the saw until the table is clear of all tools, wood scraps, etc., except the workpiece.
10. Cut only one piece at a time.
11. Provide adequate support accessories such as tables; saw horses, table extensions, etc. for workpieces wider or longer than the table top
12. Let the blade reach full speed before contacting the workpiece.
13. If the workpiece or blade becomes jammed or bogged down, turn miter saw “OFF” by releasing the switch.
14. After finishing the cut, release the switch, hold the saw arm down and wait for blade to stop before removing work or cutoff piece.
15. Turn on the dust collection system and close all gates, except that for the miter saw